Omnia.9

18 articles

Finding and Downloading the Omnia 9 SNMP MIB File

Where can I locate and download the Omnia 9 SNMP MIB file?

Updated 2 weeks ago by Mark Manolio

Scheduling a Preset Change in Omnia.9

How to use the built-in scheduler in the Omnia.9 to change presets.

Updated 2 weeks ago by Mark Manolio

Passing Low Frequency Automation Tones Through Omnia.9

Scope. How to ensue that low frequency automation tones are passed through the Omnia.9 processing properly. Problem. A customer called whose automation system uses an 18Hz triggering tone that plays…

Updated 1 month ago by Mark Manolio

Using NfRemote to Monitor Loudness

Scope. An explanation of all of the licensing options for the MPX Node and when and if they are needed. Question. What license options must I purchase for my MPX Nodes to send the same MPX stream to…

Updated 1 month ago by Mark Manolio

How do I get and use the Omnia.9 Remote Control application? (NfRemote)

Download and use the NfRemote application for the Omnia.9, Omnia.7 and Omnia.9sg.

Updated 5 months ago by Werner Gabel

Installing and using the RDS Translator for Omnia.9

Scope. This document applies specifically to the Omnia.9 with regard to sending RDS and Streaming now playing data; However, this utility could be used to translate any data to anything that can rece…

Updated 5 months ago by Bryan Jones

Help with Omnia 9 and FM and HD blending issues

Scope. This document applies to Omnia 9 audio processors running in FM + HD mode and discusses issues with HD blending. Description. A customer reports that the station runs HD, and is having issues…

Updated 5 months ago by Bryan Jones

Omnia.9 version 3.20.20 Software Install and Release Notes

Updating your Omnia.9 software is done using a USB flash drive or (preferably) the NfRemote software client. This procedure assumes you have already installed NFRemote and have access to your Omnia.9…

Updated 7 months ago by Mark Manolio

Setting Up a Studio Processing Output

Scope. This document explains how to route the low-delay studio processing audio to an output of the Omnia.9. Description. Unike most of the other processing cores in the Omnia.9, the Studio Processi…

Updated 10 months ago by Mark Manolio

Licensing and Configuring µMPX Encoder

SCOPE. This article describes how to license and configure an Omnia.9 MKII FM processor to use µMPX. DESCRIPTION. Whether you are replacing an existing STL, adding a backup link, or moving your proce…

Updated 1 year ago by Jake Alderman

Using An AES 67 Stream To Feed Omnia 9 (MkII Only)

The easiest way to use AES 67 streams with a Livewire-equipped (MkII) Omnia 9 is by using the SDP file from the AES 67 device being used with it. For example, using the Axia iQx console, I downloaded…

Updated 1 year ago by Mark Manolio

Setting Up Omnia 9 For FM Pre-Emph Output via AES/EBU

The MPX output of the Omnia 9 should be used whenever possible since the final limiter/clipper works in the composite MPX domain but sometimes this is not practical in a given air chain situation. He…

Updated 1 year ago by Mark Manolio

Do you repair Omnia 9 power supplies

Scope. This article applies to the power supplies used in the Omnia 9 audio processor regarding repair or replacement. Description. Customers will often ask if the power supplies in their Omnia 9 can…

Updated 1 year ago by Bryan Jones

Password Reset For Omnia 9

If you are locked out of your Omnia 9, touch the "Menu" button at the top of the screen and note the "Host Name" as shown there: Send that host name to Omnia Support and they will send you back a tem…

Updated 1 year ago by Mark Manolio

Easily Grabbing Task Script Paths Using NfRemote

Recent versions of the Omnia 9 (and also the 9SG and Omnia 7) have included a really cool feature called Task Scripting. Using this, just about any function of the Omnia 9 can be GPI'd or controlled…

Updated 1 year ago by Mark Manolio

Omnia Full Screen Display on Startup with NfRemote

NF REMOTE FIRST RUN. NfRemote is an application and setup program in one. Most often the installer for NF Remote is included as a download directly from your product. The most current version can be…

Updated 1 year ago by Bryan Jones

Omnia.9 version 3.20.04 software install and release notes

Updating your Omnia.9 software is done using a USB flash drive or the NfRemote client. This procedure assumes you have already installed and have access to your Omnia.9. Please refer to the Omnia.9 m…

Updated 1 year ago by Mark Manolio

What are the multi-band frequencies on the Omnia 9

The Omnia 9 processor support up to seven bands of multi-band processing. The number of bands used is adjustable by the user, however, the crossover points and Q values are preset. Slopes used are ve…

Updated 1 year ago by Bryan Jones

TelosHelp (opens in a new tab)

Powered by HelpDocs (opens in a new tab)